Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000

How to assemble a stone cage net for a riverbank erosion control project?

2026-11-06 13:01:35
How to assemble a stone cage net for a riverbank erosion control project?

PU sandwich panel production is often judged at the press and the saw, but the density pattern in the finished panel is set earlier, when polyol and isocyanate meet. In a high-pressure foaming line, the two components arrive at the mix head at counter pressures, usually in the 100 to 200 bar range, and impinge in a small chamber. The energy in that collision strips the streams into a fine emulsion before the liquid enters the panel cavity. A low-pressure mechanical mixer can blend the same chemistry, but the droplet size is coarser and the mixing time longer. Coarser emulsion means less uniform nucleation, and less uniform nucleation means density that drifts from the injection point toward the far end of the panel.

This is not a subtle lab difference. On a 6 m panel, a density swing of a few kilograms per cubic meter from gate to vent is enough to change the local thermal conductivity and the local compressive behavior. The panel still passes a visual check. The problem appears later as a soft spot under a fixing, a wavy facing after a warm day, or a thermal drift in a cold-store wall. Uniform density is a mixing and flow outcome first, a chemistry outcome second.

High Pressure Does Two Jobs in the Cavity

The first job is mixing. The second is filling. High-pressure injection sends the reacting liquid into the cavity at a velocity that helps it spread across the width before the cream time closes the flow path. That matters because PU foam has a short window between pouring and gelling. If the liquid reaches the far edge after the gel point, the foam rises in place instead of flowing, and the last section ends up with lower density and larger voids. The pressure front keeps the liquid moving while it is still low-viscosity, so the cavity fills more evenly.

Overpacking is the controlled part of this. The cavity is slightly overfilled, and the excess pressure compacts the rising foam against the facings. That compaction raises density near the surfaces and improves adhesion, but it has to be balanced. Too little overpack leaves voids at the edges. Too much puts stress on the steel facings and can bow the panel before it reaches the saw. High-pressure foaming tightens that control window but does not remove it.

Temperature and Line Speed Decide Whether the Foam Fills Evenly

A high-pressure mix head cannot compensate for cold tooling. If the steel facings or the platens are below the formulation's comfort range, the foam loses heat at the interface, the cream time stretches, and the rise profile changes across the panel. The core may show a skin that is denser than the center and a center that is coarser than the edges. The same chemistry that ran flat at 25 C can run unevenly at 15 C. Line speed interacts with this. Fast lines need the foam to fill quickly, and a cold cavity slows the flow front, so the injection pattern has to be set against both temperature and speed.

Moisture is the other variable that gets underestimated. Polyurethane reacts with water and releases carbon dioxide, which can create coarse cells and a density that looks acceptable on average but varies locally. Facings stored in a humid yard can carry enough surface moisture to affect the bond line and the foam skin. A production line that controls mix pressure but ignores facing temperature and moisture is only solving part of the uniformity problem.

What the Density Map Looks Like When Foaming Is Off

A density check taken only at the panel center will miss the common failure modes. The useful check is a map, with samples taken near the injection point, the middle, the far end, and both edges. On a good high-pressure run, the spread across those points is small and the variation follows a predictable pattern. On a poor run, the map tells a story.

Foaming setup Mixing pressure Typical density spread across 6 m panel Void pattern Cell structure at panel ends
High-pressure impingement, heated tooling 100 to 200 bar About 2 to 3 percent Few edge voids when overpack is set Fine and closed
Low-pressure mechanical mixing 5 to 20 bar About 5 to 8 percent More frequent end voids Coarser and less uniform
Preformed board insert Not applicable Depends on board fit, gaps can exceed 10 percent locally Gaps at edges and cutouts Board cell structure, but air gaps at joints

The board insert row is not a criticism of board stock. It has a different failure mode. The foam itself may be excellent, but the gaps around it are not foam, and heat moves through those gaps. High-pressure foaming closes the cavity in one shot, which is why it holds an advantage in density continuity rather than in peak R-value alone. EN 14509 treats density and thermal conductivity as declared values, so the map is part of the declaration, not a lab curiosity.

A Production Run Where End Density Told the Story

A run of 100 mm PIR panels for a cold-storage envelope once showed a density reading of about 38 kg/m3 near the injection end and 42 kg/m3 near the far end. The average was inside the declared range, so the batch almost shipped. A section cut at the far end showed a band of larger cells just under the facing and a soft edge that crumbled when probed. The cause was not the formulation. The mix pressure had drifted below the set point after a filter change, and the platens on that line were running cooler than the recipe assumed. The combination slowed the flow front and let the foam gel before it reached the end.

The fix was mechanical, not chemical. The filter was replaced, the pressure was brought back to the operating window, and the platen temperature was raised to the recipe value. The next panels showed a density spread under 3 percent across the length. The point of the case is that high-pressure foaming is a system, not a single valve. Pressure, temperature, and line speed have to be in range together, or the density map will show it.

Limits of High-Pressure Foaming and What It Cannot Fix

High-pressure foaming improves density uniformity, but it does not rescue a formulation with the wrong catalyst balance or a facings stack that is contaminated with oil. It also cannot eliminate the density gradient that comes from a very thick cavity, where the flow path is long and the foam has more time to react before it reaches the end. In those builds, injection point placement and multiple shots matter as much as mix pressure. The method is also not free. High-pressure equipment costs more to buy and maintain than a low-pressure mixer, and it demands tighter process control. For thin panels with short flow paths, the density benefit may not justify the capital cost.

Glostar Panel runs PU sandwich panel production on high-pressure foaming lines with controlled mix pressure, platen temperature, and line speed, and the quality checks include density mapping at the ends and edges rather than a single center sample. That setup supports uniform density across the panel, but it does not change the basic rule: the foam only fills evenly when the whole line is held inside its process window.

Get a Quote

Get a Free Quote

Our representative will contact you soon.
Email
Mobile/WhatsApp
Name
Company Name
Message
0/1000